I still can't ping my AMPR IP: I could receive RIPv2 password
Here is a recap of all the configuration I did:
/etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback
# The primary network interface allow-hotplug ens3 iface ens3 inet dhcp iface ens3 inet6 static address 2605:6400:20:1920:8af7:f451:cb26:a3f8 netmask 48 gateway 2605:6400:20::1
auto ampr0 iface ampr0 inet static address 44.26.0.168 netmask 255.255.255.248
/etc/rc.local
iptables -A INPUT -p 4 -j ACCEPT
## Configure Tunnel (put your ISP you received from your ISP Here). ip tunnel add ampr0 mode ipip local 209.141.42.9 ttl 255
## Bring it up ip link set dev ampr0 up
## Enable Multicast in order to receive routes ifconfig ampr0 multicast
## Configure Policy Based routing # Packets to 44/8 network use routing table 44 ip rule add to 44.0.0.0/8 table 44 priority 44
# Packets from our 44 subnet use table 44 (put your AMPRNet Subnet here) ip rule add from 44.26.0.168/29 table 44 priority 45 ip route add default dev ampr0 via 169.228.34.84 onlink table 45
## Configure static routes # Default route for table 44 is to send traffic to amprnet gateway at UCSD ip route add default dev ampr0 via 169.228.34.84 onlink table 44
# Route packets for our net to local interface (put your AMPRNet Subnet here) ip route add 44.26.0.168/29 dev ens3 table 44
## Start ampr-ripd to learn rest of mesh routes # Be sure to substitute the password you found earlier for <SecretPassword> # Put your static IP you received from your ISP here. /usr/bin/ampr-ripd -s -i ampr0 -a 209.141.42.9 -t 44 -p pLaInTeXtpAsSwD
iptables -t mangle -A PREROUTING -i ampr0 -s 44.0.0.0/9 -j RETURN iptables -t mangle -A PREROUTING -i ampr0 -s 44.128.0.0/10 -j RETURN iptables -t mangle -A PREROUTING -i ampr0 -j CONNMARK --set-mark 45 iptables -t mangle -A OUTPUT -m connmark --mark 45 -j CONNMARK --restore-mark iptables -t mangle -A PREROUTING ! -i ampr0 -m connmark --mark 45 -j CONNMARK --restore-mark
exit 0
________________________________ From: 44Net 44net-bounces+dnwk=linkun.info@mailman.ampr.org on behalf of Marius Petrescu via 44Net 44net@mailman.ampr.org Sent: Thursday, November 4, 2021 14:45 To: 44net@mailman.ampr.org 44net@mailman.ampr.org Cc: Marius Petrescu marius@yo2loj.ro Subject: Re: [44net] Tunnel setup help: Debian 11
That's because that setup does not allow that, because replies will go out your main default route, from table main.
There should be another routing table, let's say 45, holding only a single default route:
ip route add default dev ampr0 via 169.228.34.84 onlink table 45
And you need to connection mark any incoming new connection from ampr0 NOT in 44.0.0.0/9 or 44.128.0.0/10 with that connection mark, and then mark any packet with that connection mark with routing mark 45. This will ensure the replies coming from ampr0 go back the way they came in... So basically you need this:
iptables -t mangle -A PREROUTING -i ampr0 -s 44.0.0.0/9 -j RETURN
iptables -t mangle -A PREROUTING -i ampr0 -s 44.128.0.0/10 -j RETURN
iptables -t mangle -A PREROUTING -i ampr0 -j CONNMARK --set-mark 45
iptables -t mangle -A OUTPUT -m connmark --mark 45 -j CONNMARK --restore-mark
iptables -t mangle -A PREROUTING ! -i ampr0 -m connmark --mark 45 -j CONNMARK --restore-mark
But be aware, this will get the door wide open from the internet to your internal network, so setting up some firewall rules would be useful...
Marius, YO2LOJ
On 04/11/2021 23:28, KUN LIN via 44Net wrote:
Oh, when I run find_pass.sh again, I did get the ripv4 broadcast and found the password.
And then I proceed to setup rc.local as documented in that wiki article. However, I still can't ping my AMPR IP from Internet.
-- rc.local
### ## Create AMPRNet Tunnel and routing ##
## Configure Tunnel (put your ISP you received from your ISP Here). ip tunnel add ampr0 mode ipip local 209.141.42.9 ttl 255
## Bring it up ip link set dev ampr0 up
## Enable Multicast in order to receive routes ifconfig ampr0 multicast
## Configure Policy Based routing # Packets to 44/8 network use routing table 44 ip rule add to 44.0.0.0/8 table 44 priority 44
# Packets from our 44 subnet use table 44 (put your AMPRNet Subnet here) ip rule add from 44.26.0.168/29 table 44 priority 45
## Configure static routes # Default route for table 44 is to send traffic to amprnet gateway at UCSD ip route add default dev ampr0 via 169.228.34.84 onlink table 44
# Route packets for our net to local interface (put your AMPRNet Subnet here) ip route add 44.26.0.168/29 dev ens3 table 44
## Start ampr-ripd to learn rest of mesh routes # Be sure to substitute the password you found earlier for <SecretPassword> # Put your static IP you received from your ISP here. /usr/bin/ampr-ripd -s -i ampr0 -a 209.141.42.9 -t 44 -p <thepassword I received>
From: 44Net 44net-bounces+dnwk=linkun.info@mailman.ampr.org on behalf of Steve L via 44Net 44net@mailman.ampr.org Sent: Wednesday, November 3, 2021 18:46 To: 44Net general discussion 44net@mailman.ampr.org Cc: Steve L kb9mwr@gmail.com Subject: Re: [44net] Tunnel setup help: Debian 11
I have configured the public IP in the AMPR portal as gateway.
If you just did this, wait a while like a half hour.
When I try to run find_password.sh in ampr-ripd-2.4, I am stopped at Waiting for RIPv2 broadcasts... and never retrieve a password.
You don't need to run the find password script or specify a password if you are using ampr-ripd above version 1.14 (its hardcoded in the program). But I do believe even if you run that, it should retrieve it.
I usually start off really stripped down, with all firewall stuff off till I know I am receiving the protocol 4 rip broadcasts.
Do you see anything with tcpdump ? tcpdump -i eth0 -vvv host amprgw.ucsd.edu or ip proto \icmp
If not, then something upstream is blocking protocol 4 from reaching you. Seems like it might be outside of your home if your configuring the interface directly with a public IP
In the iptables world, here is the ipencap (protocol 4) syntax: iptables -A INPUT -p 4 -j ACCEPT
On Wed, Nov 3, 2021 at 6:11 PM KUN LIN via 44Net 44net@mailman.ampr.org wrote:
I have been trying to configure the AMPRtunnel for a while without success. Could someone please point me to the right direction.
I am running Debian 11 with public IP. I have configured the public IP in the AMPR portal as gateway.
I am trying to follow this document https://wiki.ampr.org/wiki/Ubuntu_Linux_Gateway_Example
When I try to run find_password.sh in ampr-ripd-2.4, I am stopped at Waiting for RIPv2 broadcasts... and never retrieve a password.
Here is what I have done so far.
in /etc/network/interfaces, I added
auto ens3:1 iface ens3:1 inet static address 44.26.0.168 netmask 255.255.255.248
Then I created ipip tunnel using following commands
ip tunnel add ampr0 mode ipip local 209.141.42.9 ttl 255 ip link set dev ampr0 up ifconfig ampr0 multicast ip rule add to 44.0.0.0/8 table 44 priority 44 ip rule add from 44.26.0.168/29 table 44 priority 45 ip route add default dev ampr0 via 169.228.34.84 onlink table 44 ip route add 44.26.0.168/29 dev ens3 table 44
Then, I run ampr-ripd -d -v -i ens3 to get the password in order to plug into lat command ampr-ripd -s -i ampr0 -a 209.141.42.9-t 44 -p <SecretPassword>
However, the find_password.sh stopped at waiting for ripv2 broadcast. Here is the logs for command
Using metric 0 for routes. Using TCP window 840 for routes. Using gateway 209.141.42.1 for direct 44net endpoints via interface ens3. Waiting for RIPv2 broadcasts...
Any idea on what am I doing wrong? Thanks
Kun
44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net
44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net _________________________________________ 44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net
_________________________________________ 44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net