13 Mar
2022
13 Mar
'22
1:36 p.m.
Hi Chris,
Give it 24 hours, updates on the IPIP mesh don’t occur in realtime.
73,
Chris - G1FEF
On 13 Mar 2022, at 17:18, C B via 44Net
<44net(a)mailman.ampr.org> wrote:
Hi
The DNS records have been set up (thanks to Ronnie)
The DNS records seem to have propagated and are functional.
The router seems to have the tunnel active.
admin@EdgeRouter-8-Port:~$ show interfaces tunnel tun0tun0@NONE:
<POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN group default
qlen 1 link/ipip 108.178.139.90 peer 169.228.34.84 Description: Tunnel to AMPRNet
gateway
RX: bytes packets errors dropped overrun mcast 4700856
13768 0 0 0 0 TX: bytes packets errors
dropped carrier collisions 2586483 42788 20 0 20
0admin@EdgeRouter-8-Port:~$
However the tracert to 8.8.8.8 stops at the local router interface.
Any help greatly appreciated.
Thank you
Chris
On Sunday, March 13, 2022, 07:38:18 AM PDT, C B via 44Net
<44net(a)mailman.ampr.org> wrote:
Thank you for the reply.
The request for DNS was sent thru the portal, by sending a message to the coordinator.
Is this the correct method to make this request? There has been no response.
Thank you.
Chris
On Sunday, March 13, 2022, 03:51:20 AM PDT, Chris Smith via 44Net
<44net(a)mailman.ampr.org> wrote:
Hi Chris,
Did you register your IP in DNS? You need an A record for your IP address (any IP
addresses you are routing) in order for it to pass the UCSD gateway out to the internet.
You can do this by asking your local coordinator or by asking myself.
73,
Chris - G1FEF
On 12 Mar 2022, at 19:06, C B via 44Net
<44net(a)mailman.ampr.org> wrote:
HI
After receiving my ip address assignment i am trying to set 44net up on my edgerouter
8.
Following the instructions for the edgerouter on the wiki, and changing the port from
eth2 to eth7 i as unable to ping thru to the internet as described in the instructions.
An edge router 4 was also set up using the wiki instructions and the same result of not
being able to ping thru to 8.8.8.8 on the edgerouter 4, thus i am continuing with the
edgerouter 8 as this would be my final configuration.
From the CLI "show interfaces tunnel tun0" the response shows traffic in both
directions thus the tunnel appears to be up.
In order to test my configuration, a edge router 4 was programmed to simulate the UCSD
end of the tunnel and a Layer 3 switch was used to simulate the internet connection.
The test setup as able to pass the IPIP traffic between the routers as expected, this
leads me to believe i may have the setup correct or at least very close.
now i am at a loss of how to troubleshoot further.
Any advice, tips, troubleshooting methods, or help of any kind is greatly appreciated.
Thank you
Chris
_________________________________________
44Net mailing list
44Net(a)mailman.ampr.org
https://mailman.ampr.org/mailman/listinfo/44net
_________________________________________
44Net mailing list
44Net(a)mailman.ampr.org
https://mailman.ampr.org/mailman/listinfo/44net
_________________________________________
44Net mailing list
44Net(a)mailman.ampr.org
https://mailman.ampr.org/mailman/listinfo/44net
_________________________________________
44Net mailing list
44Net(a)mailman.ampr.org
https://mailman.ampr.org/mailman/listinfo/44net