Hi there
Is there anyone that use AMPRNET for connecting VOIP gear (such as echolink alients (or even Digital repeaters (DMR D-STAR etc) and can tell how is the fact that every packet goes back and forth to UCSD router effect the connections ? is the latency not making any problem ?
any comments from anyone that has tried that is appreciated
Thanks Forward
Ronen - 4Z4ZQ
http://www.ronen.org
Ronen Pinchooks (4Z4ZQ) WebSite<http://www.ronen.org/>
www.ronen.orgronen.org (Ronen Pinchooks (4Z4ZQ) WebSite) is hosted by domainavenue.com
Please contact me off list please.
Thanks much!
--
<rhetorical> Why is it linux users can install and operate *any* version of M$
Windoze but the same can't be said in reverse?</rhetorical>
73 de Brian - N1URO
email: (see above)
Web: http://www.n1uro.net/
Ampr1: http://n1uro.ampr.org/
Ampr2: http://nos.n1uro.ampr.org
Linux Amateur Radio Services
axMail-Fax & URONode
http://uronode.sourceforge.nethttp://axmail.sourceforge.net
AmprNet coordinator for:
Connecticut, Delaware, Maine,
Maryland, Massachusetts,
New Hampshire, Pennsylvania,
Rhode Island, and Vermont.
I've gone through several router changes recently all requiring IP
changes due to changes of MAC. Can a good handful run:
ip route get 44.88.0.1 and show me the commercial IP listed? I've seen
several who run rip listener daemons that have failed to update my IP
(and I do have remote access to these points).
Thanks.
--
<rhetorical> Why is it linux users can install and operate *any* version of M$
Windoze but the same can't be said in reverse?</rhetorical>
73 de Brian - N1URO
email: (see above)
Web: http://www.n1uro.net/
Ampr1: http://n1uro.ampr.org/
Ampr2: http://nos.n1uro.ampr.org
Linux Amateur Radio Services
axMail-Fax & URONode
http://uronode.sourceforge.nethttp://axmail.sourceforge.net
AmprNet coordinator for:
Connecticut, Delaware, Maine,
Maryland, Massachusetts,
New Hampshire, Pennsylvania,
Rhode Island, and Vermont.
Thanks all who answered.
--
<rhetorical> Why is it linux users can install and operate *any* version of M$
Windoze but the same can't be said in reverse?</rhetorical>
73 de Brian - N1URO
email: (see above)
Web: http://www.n1uro.net/
Ampr1: http://n1uro.ampr.org/
Ampr2: http://nos.n1uro.ampr.org
Linux Amateur Radio Services
axMail-Fax & URONode
http://uronode.sourceforge.nethttp://axmail.sourceforge.net
AmprNet coordinator for:
Connecticut, Delaware, Maine,
Maryland, Massachusetts,
New Hampshire, Pennsylvania,
Rhode Island, and Vermont.
Hi All,
Sorry for the OT noise, someone emailed me some weeks back (
maybe a couple of months )
looking to link to my Node, I wonder if that person is on this list ?
If so, could you please contact me again, off list.
Thanks ..... Peter ZL2BAU
I'm presenting at the TAPR forum 9am on Friday about HamWAN and some 44net
topics.
Love to meet up with any of the other 44net users and chat after, please hit
me up of shoot me an SMS at my number below.
I'll most likely be on 223.48 simplex as well.
73's W9CR
--
Bryan Fields
727-409-1194 - Voice
727-214-2508 - Fax
http://bryanfields.net
Hi,
Is anyone still using CONVERS? I can only see autologged-in sysops in all
channels and no users.
---
73 Δημήτρης - SV1UY
73 de Demetre - SV1UY
IP Coordinator for AMPRNet in Greece
e-mail: demetre.sv1uy(a)gmail.com
Radio e-mail: sv1uy(a)winlink.org
AMPRnet e-mail: sv1uy(a)sv1uy.ampr.org
PACKET mail: SV1UY(a)SV1UY.ATH.GRC.EU
WEB: http://www.qsl.net/sv1uy
Hi all,
I've had a /29 allocation for a while but I'm just now getting set up to
try to get it working and I have a questions.
My edge router is a Cisco 1811 that I've configured a single IP-IP
tunnel on.
interface Tunnel44
no ip address
ip tcp adjust-mss 1436
tunnel source FastEthernet0
tunnel mode ipip
tunnel destination 169.228.66.251
end
The only traffic I see coming in on that interface is multicast (which I
see as being from RIPng). Are hosts on AMPR net reachable from the
public internet via the UCD gateway or is the only traffic I'll ever see
from there those RIPng packets?
And from what I'm guessing, packets sent to the UCD gateway don't get
routed to other netblocks/allocations so I'd need to goahead and build
tunnels to everyone else to get a full mesh network.
Can someone give me a suggestion on netblocks to build to just to test
things?
Thanks,
James Sharp
N5XNS
james(a)fivecats.org
Hi there
After long time Its time to replace my Cisco with the MikroTik
The Cisco will go out soon from my home to the local repeater site and deal with connecting our local P25 capable repeater with a worldwide amateur repeaters network and in addition will deal with portion of the AMPRNET network (hopefully will give the local amateurs 44 net feed Via High speed 2.4GHZ WIFI access point)
So the MikroTik will have to do what my Cisco does now and do the IPIP for my network
I saw that there has been some changes to the automatic router Scripts in the last few weeks and saw a note that one of the script consume memory and Probably wouldn't run on my home router ... Due to small memory It have
So what Script i need to take now ? and where can i take it From ? and if there is a small note how to run it
If needed it has 32M Memory and 16 M So called HDD (flash ?)
The Router is hap lite can bee seen here
http://www.routerboard.co.il/product/hap-lite
[http://www.routerboard.co.il/sites/3102/images/itempics/133463_large.jpg]<http://www.routerboard.co.il/product/hap-lite>
RouterBoard Israel??? ?????? ?????? MikroTik hAP lite ...<http://www.routerboard.co.il/product/hap-lite>
www.routerboard.co.il
RouterBoard Israel??? ?????? ?????? MikroTik hAP lite | ????? ???????? ???????? |
...
Please Advice
Thanks Forward
Ronen - 4Z4ZQ
http://www.ronen.org
Ronen Pinchooks (4Z4ZQ) WebSite<http://www.ronen.org/>
www.ronen.orgronen.org (Ronen Pinchooks (4Z4ZQ) WebSite) is hosted by domainavenue.com
