Greetings!
I have a /22 block of AMPRNet space. I've configured it for tunnel access, and defined the gateway in my portal. Following the instructions on the wiki, here is my router config:
interface GigabitEthernet0/0 ip address 44.48.8.1 255.255.252.0 secondary ip address 96.82.54.108 255.255.255.240 duplex auto speed auto media-type rj45 end
interface Tunnel0 no ip address tunnel source 96.82.54.108 tunnel mode ipip tunnel destination 169.228.66.251 end
results of 'sh int tunnel0'
amprnet-router#sh int tunnel0 Tunnel0 is up, line protocol is up Hardware is Tunnel MTU 17920 bytes, BW 100 Kbit/sec, DLY 50000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation TUNNEL, loopback not set Keepalive not set Tunnel source 96.82.54.108, destination 169.228.66.251 Tunnel protocol/transport IP/IP Tunnel TTL 255, Fast tunneling enabled Tunnel transport MTU 1480 bytes Tunnel transmit bandwidth 8000 (kbps) Tunnel receive bandwidth 8000 (kbps) Last input 00:02:16, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/0 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 7024 packets input, 3500920 bytes, 0 no buffer Received 0 broadcasts (0 IP multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 output buffer failures, 0 output buffers swapped out
At this point, I believe I need to get RIP running with the right options. However, this is where the wiki falls short. The only rip configs examples are for the linux daemons. Here is the output of 'sh ip prot'
amprnet-router#sh ip protocols *** IP Routing is NSF aware ***
Routing Protocol is "rip" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Sending updates every 30 seconds, next due in 13 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Redistributing: rip Neighbor(s): 169.228.66.251 Default version control: send version 2, receive version 2 Automatic network summarization is in effect Maximum path: 4 Routing for Networks: 44.0.0.0 Passive Interface(s): GigabitEthernet0/0 GigabitEthernet0/1 VoIP-Null0 Routing Information Sources: Gateway Distance Last Update Distance: (default is 120)
As is standard practice, I've put all interfaces in passive-default, and then explicitly defined tunnel0 as non-passive. I have not been able to establish any sort of RIP adjacency:
amprnet-router#sh ip route rip Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP + - replicated route, % - next hop override
Gateway of last resort is not set
amprnet-router#sh ip rip database 44.0.0.0/8 auto-summary 44.48.8.0/22 directly connected, GigabitEthernet0/0
Thanks in advance to anyone who can offer any guidance.
--- 73, Bill Atkinson, NF9K ARRL Technical Specialist ARRL VE/OO Laurel VE PODXS 070 Club #1595 30MDG #6014
www.nf9k.net www.crossroadsdmr.org