Hi Please help me to understand, the difference between the single tunnel and a gateway part of the 44net mesh? The primary use will be to use is connecting p-25 repeaters and allstar link repeaters. Thank you Chris N6LXX
On Tuesday, March 15, 2022, 04:13:47 AM PDT, Marius Petrescu marius@yo2loj.ro wrote:
The first one only sets up a single tunnel to amprgw, not a gateway part of the 44net mesh.
Marius, YO2LOJ
On 15/03/2022 13:10, C B via 44Net wrote:
HI The first set was used as they seemed to better match the hardware being used. Chris N6LXX
On Monday, March 14, 2022, 05:25:21 PM PDT, Lee D Bengston via 44Net 44net@mailman.ampr.org wrote: Which set of instructions for the Edgerouter did you use? I used the second set in the Wiki, which is more complete. I recall from a previous discussion in this group that someone else tried the first set, didn't have any luck, and started over with the second set, which worked.
Lee K5DAT
On Mon, Mar 14, 2022, 6:57 PM C B via 44Net 44net@mailman.ampr.org wrote:
HI Still not able to ping to the internet or from the internet to the edgerouter. Outbound pings stop at the gateway on the edgerouter. When pining from the internet towards the edgerouter (from a different location) get as far as 132.239.255.50 The the IPIP tunnel in the edgerouter appears up with traffic in both directions. Any help is greatly appreciated. Chris N6LXX
On Sunday, March 13, 2022, 10:48:50 AM PDT, C B via 44Net < 44net@mailman.ampr.org> wrote:
Ok cool, i will wait. Thanks for the reply! Chris On Sunday, March 13, 2022, 10:37:28 AM PDT, Chris Smith via 44Net < 44net@mailman.ampr.org> wrote:
Hi Chris,
Give it 24 hours, updates on the IPIP mesh don’t occur in realtime.
73, Chris - G1FEF
On 13 Mar 2022, at 17:18, C B via 44Net 44net@mailman.ampr.org wrote:
Hi The DNS records have been set up (thanks to Ronnie) The DNS records seem to have propagated and are functional. The router seems to have the tunnel active. admin@EdgeRouter-8-Port:~$ show interfaces tunnel tun0tun0@NONE:
<POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN group default qlen 1 link/ipip 108.178.139.90 peer 169.228.34.84 Description: Tunnel to AMPRNet gateway
RX: bytes packets errors dropped overrun mcast
4700856 13768 0 0 0 0 TX: bytes packets errors dropped carrier collisions 2586483 42788 20 0 20 0admin@EdgeRouter-8-Port :~$
However the tracert to 8.8.8.8 stops at the local router interface. Any help greatly appreciated. Thank you Chris
On Sunday, March 13, 2022, 07:38:18 AM PDT, C B via 44Net <
44net@mailman.ampr.org> wrote:
Thank you for the reply. The request for DNS was sent thru the portal, by sending a message to
the coordinator.
Is this the correct method to make this request? There has been no
response.
Thank you. Chris
On Sunday, March 13, 2022, 03:51:20 AM PDT, Chris Smith via 44Net <
44net@mailman.ampr.org> wrote:
Hi Chris,
Did you register your IP in DNS? You need an A record for your IP
address (any IP addresses you are routing) in order for it to pass the UCSD gateway out to the internet.
You can do this by asking your local coordinator or by asking myself.
73, Chris - G1FEF
On 12 Mar 2022, at 19:06, C B via 44Net 44net@mailman.ampr.org wrote:
HI After receiving my ip address assignment i am trying to set 44net up
on my edgerouter 8.
Following the instructions for the edgerouter on the wiki, and changing
the port from eth2 to eth7 i as unable to ping thru to the internet as described in the instructions.
An edge router 4 was also set up using the wiki instructions and the
same result of not being able to ping thru to 8.8.8.8 on the edgerouter 4, thus i am continuing with the edgerouter 8 as this would be my final configuration.
From the CLI "show interfaces tunnel tun0" the response shows traffic
in both directions thus the tunnel appears to be up.
In order to test my configuration, a edge router 4 was programmed to
simulate the UCSD end of the tunnel and a Layer 3 switch was used to simulate the internet connection.
The test setup as able to pass the IPIP traffic between the routers as
expected, this leads me to believe i may have the setup correct or at least very close.
now i am at a loss of how to troubleshoot further. Any advice, tips, troubleshooting methods, or help of any kind is
greatly appreciated.
Thank you Chris
44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net
44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net
44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net
44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net
44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net
44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net
44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net
44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net _________________________________________ 44Net mailing list 44Net@mailman.ampr.org https://mailman.ampr.org/mailman/listinfo/44net