Hi all,
I'm new to amprnet and linux and try to get my RaspberryPi connected with the 44net. I have setup the Pi and configured IPIP tunl0. I can ping to 44.137.0.0/16. The problem is that I do not receive any RIPv2 packets with ampr-ripd or rip44d. The situation is that the Pi is behind the DMZ of my ISP router and I think that's causing the problem. Have try ed the cron as a 1 minute ping as suggested at http://n1uro.ampr.org/linuxconf/amprnat.txt but without result.
Do you have any suggestions or advise on what to do to get this running?
73, Fred/PA8F
The instructions I have seen and used say to put the machine outside your DMZ. I get the RIP updates.
My router allows me ONE ip address to expose to the internet and that's where my gateway sits.
-- Mitch Winkle http://ewamjlu.blogspot.com ...How long will you go limping between two different opinions? If the LORD is God, follow him... 1 Kings 18 ESV
On Thu, May 14, 2015 at 1:55 PM, Fred Boogaard pa8f@ziggo.nl wrote:
(Please trim inclusions from previous messages) _______________________________________________ Hi all,
I'm new to amprnet and linux and try to get my RaspberryPi connected with the 44net. I have setup the Pi and configured IPIP tunl0. I can ping to 44.137.0.0/16. The problem is that I do not receive any RIPv2 packets with ampr-ripd or rip44d. The situation is that the Pi is behind the DMZ of my ISP router and I think that's causing the problem. Have try ed the cron as a 1 minute ping as suggested at http://n1uro.ampr.org/linuxconf/amprnat.txt but without result.
Do you have any suggestions or advise on what to do to get this running?
73, Fred/PA8F _________________________________________ 44Net mailing list 44Net@hamradio.ucsd.edu http://hamradio.ucsd.edu/mailman/listinfo/44net
Mitch,
How about joining with myself and others behind NAT and a single (generally dynamic) public IP address that are looking to something easier and less complicated than the present IPIP tunnel method in use. Might you like to join a few others in connecting to 44net over something easy and standard such as IPsec, OpenVPN, or PPTP? if you do, NAT becomes a non issue as the pi sets up an outbound point to point tunnel and the pi gains a tunnel interface that looks like any other, then you can do things on the pi as you wish.... or even easier just buy a decent router for your home network that does vpn on the router and boom, it's done for all devices on your lan as the subnet just shows up ready to use.
Eric
On Thu, May 14, 2015 at 11:57 AM, Mitch Winkle mitchwinkle@gmail.com wrote:
(Please trim inclusions from previous messages) _______________________________________________ The instructions I have seen and used say to put the machine outside your DMZ. I get the RIP updates.
My router allows me ONE ip address to expose to the internet and that's where my gateway sits.
-- Mitch Winkle http://ewamjlu.blogspot.com ...How long will you go limping between two different opinions? If the LORD is God, follow him... 1 Kings 18 ESV
On Thu, May 14, 2015 at 1:55 PM, Fred Boogaard pa8f@ziggo.nl wrote:
(Please trim inclusions from previous messages) _______________________________________________ Hi all,
I'm new to amprnet and linux and try to get my RaspberryPi connected with the 44net. I have setup the Pi and configured IPIP tunl0. I can ping to 44.137.0.0/16. The problem is that I do not receive any RIPv2 packets with ampr-ripd or rip44d. The situation is that the Pi is behind the DMZ of my ISP router and I think that's causing the problem. Have try ed the cron as a 1 minute ping as suggested at http://n1uro.ampr.org/linuxconf/amprnat.txt but without result.
Do you have any suggestions or advise on what to do to get this running?
73, Fred/PA8F _________________________________________ 44Net mailing list 44Net@hamradio.ucsd.edu http://hamradio.ucsd.edu/mailman/listinfo/44net
-
Eric Fort -
Fred Boogaard -
Mitch Winkle