Hello,I am having an issue with the routes script for the Mikrotik routers. I got through all the steps to get RIP working and routes began populating based of the guides here: http://wiki.ampr.org/wiki/Setting_up_a_gateway_on_MikroTik_Routers%C2%A0. Then I got the latest script from http://www.yo2loj.ro/%C2%A0version 3.1, while ssh'd into the box I copied and pasted the script http://www.yo2loj.ro/hamprojects/ampr-gw-3.1.rsc%C2%A0into the terminal. I used my public IP address in the AmprPublicIp field and my AMPRnet IP assigned to the DMZ IP address 44.68.204.1 then ran the update_amprgw script. At first I thought it was working but not all of the routes appear to be populating. I am only seeing 55 interfaces, much less than the 400+ I would expect. Any advise on this issue?ThanksMark ScranoK2EXE
Hi,
I understand you are behind a router in a DMZ.
In this case, your AmprPublicIp field should be the address of your primary router in the DMZ, not the real external public address.
Anyway, you should get some 430+ interfaces.
On 30.06.2017 00:34, Mark Scrano via 44Net wrote:
Hello,I am having an issue with the routes script for the Mikrotik routers. I got through all the steps to get RIP working and routes began populating based of the guides here: http://wiki.ampr.org/wiki/Setting_up_a_gateway_on_MikroTik_Routers . Then I got the latest script from http://www.yo2loj.ro/ version 3.1, while ssh'd into the box I copied and pasted the script http://www.yo2loj.ro/hamprojects/ampr-gw-3.1.rsc into the terminal. I used my public IP address in the AmprPublicIp field and my AMPRnet IP assigned to the DMZ IP address 44.68.204.1 then ran the update_amprgw script. At first I thought it was working but not all of the routes appear to be populating. I am only seeing 55 interfaces, much less than the 400+ I would expect. Any advise on this issue?ThanksMark ScranoK2EXE
Rectification, i wrote it wrong.
Your AmprPublicIp must be the WAN interface address, in your case the one assigned in the DMZ.
This address is used as the local ip of the tunnel interfaces.
On 30.06.2017 02:37, Marius Petrescu wrote:
Hi,
I understand you are behind a router in a DMZ.
In this case, your AmprPublicIp field should be the address of your primary router in the DMZ, not the real external public address.
Anyway, you should get some 430+ interfaces.
On 30.06.2017 00:34, Mark Scrano via 44Net wrote:
Hello,I am having an issue with the routes script for the Mikrotik routers. I got through all the steps to get RIP working and routes began populating based of the guides here: http://wiki.ampr.org/wiki/Setting_up_a_gateway_on_MikroTik_Routers . Then I got the latest script from http://www.yo2loj.ro/ version 3.1, while ssh'd into the box I copied and pasted the script http://www.yo2loj.ro/hamprojects/ampr-gw-3.1.rsc into the terminal. I used my public IP address in the AmprPublicIp field and my AMPRnet IP assigned to the DMZ IP address 44.68.204.1 then ran the update_amprgw script. At first I thought it was working but not all of the routes appear to be populating. I am only seeing 55 interfaces, much less than the 400+ I would expect. Any advise on this issue?ThanksMark ScranoK2EXE
Ah I figured it out the issue was on my end I did not update the gateway interface. After I changed it to "outside" and quickly the interfaces/routes began to fill in for me. However I am not able to reach sites hosted on 44net any longer. I have attached a relevant screenshot showing my ampr_config script. Thanks again.Mark K2EXE
On Thursday, June 29, 2017, 7:40:11 PM EDT, Marius Petrescu marius@yo2loj.ro wrote:
Rectification, i wrote it wrong.
Your AmprPublicIp must be the WAN interface address, in your case the one assigned in the DMZ.
This address is used as the local ip of the tunnel interfaces.
On 30.06.2017 02:37, Marius Petrescu wrote:
Hi,
I understand you are behind a router in a DMZ.
In this case, your AmprPublicIp field should be the address of your primary router in the DMZ, not the real external public address.
Anyway, you should get some 430+ interfaces.
On 30.06.2017 00:34, Mark Scrano via 44Net wrote:
Hello,I am having an issue with the routes script for the Mikrotik routers. I got through all the steps to get RIP working and routes began populating based of the guides here: http://wiki.ampr.org/wiki/Setting_up_a_gateway_on_MikroTik_Routers . Then I got the latest script from http://www.yo2loj.ro/ version 3.1, while ssh'd into the box I copied and pasted the script http://www.yo2loj.ro/hamprojects/ampr-gw-3.1.rsc into the terminal. I used my public IP address in the AmprPublicIp field and my AMPRnet IP assigned to the DMZ IP address 44.68.204.1 then ran the update_amprgw script. At first I thought it was working but not all of the routes appear to be populating. I am only seeing 55 interfaces, much less than the 400+ I would expect. Any advise on this issue?ThanksMark ScranoK2EXE
On Thursday, June 29, 2017, 9:20:59 PM EDT, Mark Scrano via 44Net 44net@hamradio.ucsd.edu wrote:
Ah I figured it out the issue was on my end I did not update the gateway interface. After I changed it to "outside" and quickly the interfaces/routes began to fill in for me. However I am not able to reach sites hosted on 44net any longer. I have attached a relevant screenshot showing my ampr_config script. Thanks again.Mark K2EXE
On Thursday, June 29, 2017, 7:40:11 PM EDT, Marius Petrescu marius@yo2loj.ro wrote:
Rectification, i wrote it wrong.
Your AmprPublicIp must be the WAN interface address, in your case the one assigned in the DMZ.
This address is used as the local ip of the tunnel interfaces.
On 30.06.2017 02:37, Marius Petrescu wrote:
Hi,
I understand you are behind a router in a DMZ.
In this case, your AmprPublicIp field should be the address of your primary router in the DMZ, not the real external public address.
Anyway, you should get some 430+ interfaces.
On 30.06.2017 00:34, Mark Scrano via 44Net wrote:
Hello,I am having an issue with the routes script for the Mikrotik routers. I got through all the steps to get RIP working and routes began populating based of the guides here: http://wiki.ampr.org/wiki/Setting_up_a_gateway_on_MikroTik_Routers . Then I got the latest script from http://www.yo2loj.ro/ version 3.1, while ssh'd into the box I copied and pasted the script http://www.yo2loj.ro/hamprojects/ampr-gw-3.1.rsc into the terminal. I used my public IP address in the AmprPublicIp field and my AMPRnet IP assigned to the DMZ IP address 44.68.204.1 then ran the update_amprgw script. At first I thought it was working but not all of the routes appear to be populating. I am only seeing 55 interfaces, much less than the 400+ I would expect. Any advise on this issue?ThanksMark ScranoK2EXE
-
Brian Kantor -
Marius Petrescu -
Mark Scrano